Aluminum foil for transformer winding

Chalco Aluminum is professional on aluminum foil for transformer winding, normally such foil in coils to be used in winding of transformers. The materials is normally high purity of aluminum above 99.65%, and in soft temper which is good for winding; Also edge free of burrs, so as to make it safe when lamination with insulation film; Also the surface is free of oil, scratches, deformations, so as could be laminated with insulation film properly.

Aluminum foil for transformer winding

Package delivery

The surface is clean, smooth and free from deformation and defects

All dimensions are deburring, precision cutting seam

  1. Alloy and Dimensions:

Alloy: 1050, 1350, 1060, 1070

Temper: O

The aplicalbe dimension of sheet shall conform to table 1.

Table1                Unit: mm

Thickness

0.3 to 2.4

Width

25 to 1250

  1. Mechanical properties and electric conductivity

   Table 3

Thickness(mm)

Tensile Strength

Kgf/mm2

Elongation

%

Bending 180 buckling inside radius

Electric conductivity at 20 ℃

Over 0.3 to 0.5

Less than 9.0

20 min.

Close contact

62.5 min.

Over 0.5 to 0.8

25 min.

Over 0.8 to 1.3

30 min.

Over 1.3 to 2.0

35 min.

Over 2.0 to 2.4

35 min

  1. Dimensions shall confom to Table 4 which indicates dimensional tolerances.

Thickness(mm)

Tolerance in hickness(mm)

Tolerance in width(mm)

Over 0.3 to 0.5

±0.02

25 to 300

Over 300 to 600

Over 600 to 1250

Over 0.5 to 0.8

±0.03

±0.3

±0.5

±1.0

Over 0.8 to 1.3

±0.04

Over 1.3 to 2.0

±0.04

Over 2.0 to 2.4

±0.05

  1. External appearance

(a).The surfaces of aluminum foil is clean and smooth, free of noious defects for use such as wrinkles, distortion and flaws. The aluminum edge in particular shall be free of flaws.

(b).The aluminum foil surface is free of oil, grease, soapy water and metal powder.

(c).The edges of aluminum foil shall be in accordance with following consitions.

All size are deburred, precision slit :

    For the thickness < 0.8mm=> Burr< 0.01mm

    For the thickness >0.8mm => Burr < 0.02mm

Round edge is available but cost shall be very high, due to the round edge processing is quite slow, and one roll by one roll processing.

  1. Packing: Eye to wall and Eye to sky two types.

ID: 250mm, 305mm, 405mm, 505mm

Eye to sky: Rolls must be placed horizontally on a pallet large and solid enough to support the weight and protect the rolls.  Two cardboards shall be placed between the rolls as dividers so that the aluminum edge be protected against friction.  The entire charge must be solidly fixed to the pallet and covered with a plastic film.

Eye to wall: Rolls must be placed vertically on a pallet large and solid enough to support the weight and adequately protect the rolls.  Two cardboards shall be placed between each roll.  The entire charge should be covered with a plastic film.

Get In Touch,Let's talk

Hello! If you are interested in our products and leave your demand, we will give you an accounting quotation in time.
Or you can send your request to our email address: info@chalcoaluminum.com

Send Your Request
  • 0086-371- 55689814 55686476
  • info@chalcoaluminum.com
  • 126#4 Building A,No.89 Science Avenue,National HI-Tech Industry Development Zone,Zhengzhou,Henan
Social touch

contact us
Get a quote Leave Message
Hi,may I help you with products, price, etc?